REV-21-1650-V1.1 NEO V1.1 motor, 60 mm body, 8 mm keyed shaft
MPN REV-21-1650-V1.1 · frc-motor
Use it
(import "parts/frc-motor/REV-21-1650-V1.1.ik" as p)In a design on ink: ask your agent for it by name, or by what it must be.
Dimensions
| body-diameter | 60 |
| body-length | 58.25 |
| pilot-diameter | 19.05 |
| pilot-height | 3.5 |
| shaft-tip | 35 |
| shaft-diameter | 8 |
Frames
Where it connects: each frame sits on the face it connects by, z out of the part, in the part's own coordinates.
| Of | Frame | Origin | x | z |
|---|---|---|---|---|
| motor | mount | (0, 0, 0) | (1, 0, 0) | (0, 0, 1) |
| motor | shaft | (0, 0, 35) | (1, 0, 0) | (0, 0, 1) |
| housing | mount | (0, 0, 0) | (1, 0, 0) | (0, 0, 1) |
| rotor | shaft | (0, 0, 35) | (1, 0, 0) | (0, 0, 1) |
| drive (assembly) | mount | (0, 0, 0) | (1, 0, 0) | (0, 0, 1) |
| drive (assembly) | shaft | (0, 0, 35) | (1, 0, 0) | (0, 0, 1) |
All 69 numbers in its record
| body-diameter | 60 |
| body-length | 58.25 |
| pilot-diameter | 19.05 |
| pilot-height | 3.5 |
| shaft-tip | 35 |
| shaft-diameter | 8 |
| shaft-style | 1 |
| mount-holes | 25.4, 0, 4.0386, 5, 17.96051, 17.96051, 4.0386, 5, 0, 25.4, 4.0386, 5, -25.4, 0, 4.0386, 5, -17.96051, -17.96051, 4.0386, 5, 0, -25.4, 4.0386, 5, 17.96051, -17.96051, 4.0386, 5 |
| pitch-circle | 50.8 |
| mount-angles-deg | 0, 45, 90, 180, 225, 270, 315 |
| mount-hole-depth | 5 |
| key-width | 2 |
| key-floor | 2.8 |
| key-start | 6 |
| key-end | 30 |
| shaft-end-bore | 4.0386 |
| shaft-end-depth | 15.08 |
| spline-teeth | 0 |
| spline-module | 0 |
| spline-pa | 0 |
| through-hex | 0 |
| rear-boss-length | 0 |
| rear-boss-diameter | 0 |
| visual-style | 0 |
| front-bevel | 0.8 |
| front-cap-length | 7 |
| rear-cap-length | 8 |
| rear-taper | 1.2 |
| seam-depth | 0.4 |
| seam-half-width | 0.25 |
| vent-count | 0 |
| vent-depth | 2 |
| vent-width | 4 |
| vent-length | 5 |
| vent-z | -48.3 |
| wire-width | 12 |
| wire-length | 4 |
| wire-z | 5 |
| label-half-width | 14 |
| label-height | 5 |
| label-z-fraction | 0.52 |
| voltage-v | 12 |
| free-speed-rpm | 5676 |
| stall-torque-nm | 2.6 |
| stall-current-a | 105 |
| free-current-a | 1.8 |
| mass-g | 425 |
| mount-thread-major-mm | 4.826 |
| mount-thread-pitch-mm | 0.79375 |
| can-front-radius | 30 |
| can-draft-deg | 1 |
| edge-radius | 0.5 |
| pilot-edge-radius | 0.5 |
| shaft-edge-radius | 0.5 |
| rear-bore-diameter | 4.0386 |
| rear-bore-depth | 2.54 |
| drill-point-z | 18.70668 |
| center | -21.20674, 21.08887, -5.298386 |
| out | -0.7069991, 0.7069991, -0.017452 |
| across | 0.7072145, 0.7067837, -0.01744709 |
| up | -2.85187e-7, -0.02467739, -0.9996955 |
| half-centres | 6.7 |
| radius | 2.8 |
| draft-deg | 5 |
| end | 5 |
| bounds | -31.151, 13.124, -8.268, -13.283, 31.031, -2.299 |
| point-mm | -29.65688, 19.70894, -5.376917, -26.44003, 22.92661, -5.343755, -23.22172, 26.14296, -5.423151, -20.0034, 29.35932, -5.502548 |
| direction | -0.7069991, 0.7069991, -0.017452, -0.7069991, 0.7069991, -0.017452, -0.7069991, 0.7069991, -0.017452, -0.7069991, 0.7069991, -0.017452 |
| radius-mm | 2, 2.25, 2.25, 2.25 |